Wind and Solar Charge Controller w/ LED Display & 600 Watt Divert Load

Description

YOU ARE BUYING ONE MISSOURI WIND 12 VOLT 440 AMP
10,000 WATT DIGITAL CHARGE CONTROLLER WITH DIVERT LOAD
THE MISSOURI WIND COMBO 440 amp CHARGE CONTROLLER
MADE IN SEYMOUR, MISSOURI
Connect wind and solar at the same time !
LOWEST COST 440 AMP CHARGE OR DIVERT CONTROLLER WITH DIVERT LOAD ON THE MARKET
ALL STEEL CONSTRUCTION
Designed, assembled, and quality checked in Missouri USA using global parts.
IT CAN DISCONNECT THE INCOMING POWER OR DIVERT IT.
Comes with 5 feet of heavy duty cables.
Comes completely prewired as shown above.
Charge controller with 600 watt divert load.
Assembled and quality checked by Missouri Wind and Solar in Seymour, Missouri. Assembled using tried and tested global parts.
This diversion controller has most of the features of our larger controller, but is much more compact and economical due to to the fact it is specifically designed
for 12 volt systems.
Some of the key features of this controller are:
Microprocessor controlled -- This is very important for both stability and functionality.
User changeable settings -- Several controllers on the market set the dump level, and that's that!
You can change the dump point voltage level, end of dump voltage level, and length of time in divert mode when end dump point voltage is reached (between 0 to 999 seconds, or 0 to 999 minutes). The controller will also monitor the diversion/disconnect activity and increase it's duration several times when your batteries are full. This feature is also adjustable.
High amp rating
-
Can be operated at 100% duty cycle conducting
surge
loads up to 440 amps or 10,000 watts.
Please note that the normally closed contacts can handle 100 amps continuous duty.
Battery status LED - Several controllers do not tell you what's going on - This one does!
Push to test. Ever wonder if your controller & load are working OK?
Long leads for easy termination.
Can divert the source from the batteries to the load, or dump both the batteries along with the source.
Some specifics about the points made above.
The microprocessor is the heart of the controller
.
It is given the battery voltage and the user changeable trip points. This information is analyzed and acted upon.
green
means the battery is full.
The
red
LED is illuminated when the battery is being dumped (or the charge source diverted.)
The dump remains active for a minimum of 5 seconds, at which time it is checked by the microprocessor. If battery voltage drops below the "Dump Cancel " level, the dump is disabled, otherwise the dump is continued and rechecked every 5 seconds.
When you click the "TEST" push-button - the 5 second cycle is started (one time, unless the batteries are within the "Dump Start" and "Dump Cancel" zone.)
Settings are user changeable!! By simply turning a simple potentiometer with a small screwdriver, you can quickly adjust the trip point.
Click picture below for our heavy duty disconnect box!
Be aware of cheap, less capable knock-offs of our model controller that are too basic to properly charge a battery. They will attempt to only turn ON and OFF for the SAME length of time, every time, when your battery is full. This will constantly boil your battery when it's full or not properly fill it or both. An improperly charged battery will have a short life and cannot be brought back. One to two years instead of 10 years or more life! You don't benefit from returning a product after it ruins your system. A charge controller must operate a relay whether mechanical or solid state(SSRs). The relay turns the charging from your solar, wind, hydro ON or OFF to your batteries. If you have 100 amps of solar charging being turned ON and OFF to your batteries you NEED to vary the time between the ON/OFF cycles. Our controller has custom programming that cannot be duplicated by the Dime Store sellers and is, of course, user changeable. Ours will more slowly top-off your battery! It will do this by adjusting itself every time your battery is full by increasing the duration of the next OFF cycle by up to 4 increased OFF times. For example: 5 seconds to 10, then 10 to 20, then 20 to 40 and will maintain a 40 second OFF time. You can adjust the starting 5 seconds down to 1 or up to 999. We even went a step further and programmed in a "sweep time" which is a secondary sensing timer that starts directly following an ON cycle. This tells the controller that it has or has not been too long before battery charging is needed again. The user adjustable sweep time allows the user and controller to have a wide range of charging times on any size battery bank. We also pre-wire and pre-program ours for you to be able to get up and going without becoming an expert. You're taking a risk with your system if accepting a too-good-to-be-true price or product description. If you're not convinced this is the controller for you, please check our other charge controllers or ask us which one is right for you.
Lowest Cost 440 AMP
Wind
&
Solar Controller with divert load
MADE WITH INDUSTRIAL RESISTORS
CLICK HERE TO SEE OUR FULL LINE OF WIND AND SOLAR PRODUCTS!
We do not mark items as gifts or under report values for customs. For International buyers,
it is strongly recommended to check your own country's tax practices as we do not
pay your taxes, duty or customs fees.
We do not over charge for shipping; it is simply what the shipping calculator comes up with.
Customs fees or taxes are not included in shipping, it is your responsibility to pay them.
UPS orders shipped signature required at our discretion!! Contact us right away if you need to make other arrangements!
Products may be slightly different than the ones pictured. If our supplier runs short of the products shown, we will substitute them for the same quality or better.
Missouri Wind and Solar provides a 90 day limited warranty on items manufactured in-house. Warranty covers workmanship and manufacturer defects. 90 day warranty begins at date of purchase and is non-transferable.
Customer is responsible for all shipping costs and must provide proof of purchase.
Warranty does not apply to:
Damage from marine use and/or saltwater environments
Corrosion due to saltwater air
Misuse
Faulty installation
Application outside manufacturer recommendations